油压浅深喉冲床

 油压浅深喉冲床Oil pressure light deep throat punch press

是我公司根据多年油压深喉冲床生产加工经验，基于节能、环保、经济、实用发展起来的一款组合油压冲床，具备油压冲床的所有优点。整机将油压深喉冲床和浅喉冲床合二为一，共用一套液压系统，两套独立的电气控制箱，可同时、独立控制操作。浅喉冲床部位配剪角模，深喉部位配折弯模或冲孔模，组成铁板剪角、冲孔、折弯实用的组合油压冲床，减少了设备投资，降低了生产成本，充分提高整机的使用效率。

Is our company according to the hydraulic deep throat punch press for many years production experience, developed based on energy-saving, environmental protection, economic and practical combination of a hydraulic press, hydraulic press with all the advantages. Machine combination of hydraulic and shallow throat deep throat punch press, shared set of hydraulic systems, two independent sets of electrical control box, can be controlled at the same time, independent operation. Shallow throat punching parts equipped with shear angle mould, deep throat sites equipped with piercing die for the bending die or to form iron notching, punching, bending and practical combination of hydraulic presses, reducing equipment investment, reduce production costs, fully improve efficiency.

主要特点：Main features:

1．         根据工程结构力学特征，将冲床深喉口边设计为低吨位深喉冲床，利用同一机身增加尾部浅喉口，得到高吨位的浅喉冲床，充分利用了钢构机架，降低了冲床的制造成本，最终减少了客户设备投资。

1. Based on the engineering characteristics of structural mechanics, punching deep throat deep throat mouth design for low-tonnage presses, using the same fuselage to increase the tail light throat, high tonnage of shallow throat punch, full use of the steel frame, reduce the manufacturing cost of punch, eventually reducing customer equipment investment.

2．         根据冲床的间隙负载特性，利用一套液压系统提供前后两台冲床的冲压力，充分利用液压系统，减少了电费，降低了生产成本。

According to punch clearance load characteristics, provided two punches in before and after using a hydraulic system pressure, take full advantage of hydraulic systems, reducing tariffs, reducing production costs.

3．         油压深喉冲床部位：深喉口C型机架，工件上下方便、整板上机无加工死角,为大钣金冲压加工之实用组合冲床。

Hydraulic deep throat punch press site: deep throat c-frame, work from top to bottom, on the entire Board without processing the dead angle, as the practical combination punch the punching process.

4．        油压浅喉冲床部位：安装在油压深喉冲床尾部，可单独作浅喉冲床使用。配上专用剪角模,可作标准剪角机使用，剪角模上配有工作台，利于工件平展冲压，工作台上有45度、横向、纵向标尺，并且标尺上有可调档位，无须对工件划线,免看线即可准确剪方角、斜角，极大的提高了工作效率和工件品质。

Oil pressure light throat punch site: installed in the tail of the hydraulic deep throat punch press, can be used solely as a light punch throat. Accompanied by a special notching die, standard notching machine,

20-60ton油压浅深喉冲床主要规格及参数：

20-60ton oil pressure light deep throat punch press main specifications and technical parameters:

注：联系我时，请说是在“傲立机床网”上看到的，谢谢！